Fence Quote Calculator
When to Use
- - Reese asks to "quote a fence job" or "run a takeoff"
- Any mention of calculating fence materials, posts, pickets, concrete, or gates
- Pricing or estimating a fence project
Material Specifications
Post Types & Spacing
- - Line posts, corner posts, end posts: 4x4 pressure treated
- Gate posts: 6x6 pressure treated (1 per single gate opening, 2 per double gate opening)
- Post spacing: 8 feet on center
Post Count Formula
- 1. Calculate total line sections:
total_linear_feet / 8 (round up) - End posts = 2 per fence run (start and end of each continuous run)
- Corner posts = 1 per corner
- Line posts = totalsections - 1 - cornerposts (per run)
- Gate posts: count based on gate config (see gates below)
Rails
- - 3x 2x4x8 rails per 8-foot section
- 3x 2x4x8 per gate leaf (for gate framing)
Pickets (Wood Fence)
- - Type: 1x6x6 dog ear pressure treated
- Coverage: 5.5 inches per picket (actual board width, no gap/waste factor)
- Per 8-foot section:
96 inches / 5.5 inches = 17.45 -> 18 pickets per section (round up) - Total pickets: sections x 18
Concrete
- - 4x4 posts: 60 lbs per post
- 6x6 posts: 80 lbs per post
- Aluminum posts: 60 lbs per post
- Vinyl posts: 80 lbs per post
- Bag size: 80 lb bags ONLY (Home Depot, 42 bags per pallet)
- Bags per 4x4:
60/80 = 0.75 -> round up to 1 bag per 4x4 post - Bags per 6x6:
80/80 = 1 bag per 6x6 post
Gates
- - Standard single gate: 5 feet wide opening (4 feet if specifically requested)
- Standard double gate: 10 feet wide opening (8 feet if specifically requested)
- Hardware per gate opening: 1 latch + 1 handle
- Hinges: 3 per gate leaf (single gate = 3 hinges, double gate = 6 hinges)
- Drop rod: 1 per double gate
Fence Types Supported
- 1. Wood (PT pine, dog ear pickets)
- Tan Vinyl
- White Vinyl
- 5ft Aluminum
- 4ft Aluminum
Output Format
When calculating a quote, present results as:
CODEBLOCK0
Important Notes
- - Always round up on pickets and posts. Short materials means a return trip.
- If Reese gives you a rough sketch or describes corners/gates, confirm the layout before running numbers.
- For vinyl and aluminum, post spacing and section widths may differ from wood. Ask Reese to confirm if specs differ from the 8' OC standard.
- Do NOT estimate labor costs in this skill. That's separate pricing.
围栏报价计算器
使用场景
- - 当Reese要求报价围栏工程或进行材料估算时
- 任何涉及计算围栏材料、立柱、栅栏板、混凝土或大门的情况
- 围栏项目的定价或预算估算
材料规格
立柱类型与间距
- - 中间立柱、角柱、端柱：4x4加压处理木材
- 大门立柱：6x6加压处理木材（单扇大门每处1根，双扇大门每处2根）
- 立柱间距：中心间距8英尺
立柱数量计算公式
- 1. 计算总直线段数：总长度英尺数 / 8（向上取整）
- 端柱数量 = 每段围栏2根（每段连续围栏的起点和终点）
- 角柱数量 = 每个转角1根
- 中间立柱数量 = 总段数 - 1 - 角柱数量（每段围栏）
- 大门立柱：根据大门配置计算（见下方大门部分）
横梁
- - 每8英尺段需3根2x4x8横梁
- 每扇大门门扇需3根2x4x8横梁（用于大门框架）
栅栏板（木围栏）
- - 类型：1x6x6狗耳形加压处理木材
- 覆盖宽度：每块栅栏板5.5英寸（实际板宽，无间隙/损耗系数）
- 每8英尺段：96英寸 / 5.5英寸 = 17.45 -> 每段18块栅栏板（向上取整）
- 栅栏板总数：段数 x 18
混凝土
- - 4x4立柱：每根60磅
- 6x6立柱：每根80磅
- 铝制立柱：每根60磅
- 乙烯基立柱：每根80磅
- 袋装规格：仅限80磅袋装（家得宝，每托盘42袋）
- 每根4x4立柱所需袋数：60/80 = 0.75 -> 向上取整为每根4x4立柱1袋
- 每根6x6立柱所需袋数：80/80 = 每根6x6立柱1袋
大门
- - 标准单扇大门：5英尺宽开口（如有特殊要求可为4英尺）
- 标准双扇大门：10英尺宽开口（如有特殊要求可为8英尺）
- 每处大门开口五金件：1个门闩 + 1个把手
- 合页：每扇门扇3个（单扇大门=3个合页，双扇大门=6个合页）
- 插销：每扇双扇大门1个
支持的围栏类型
- 1. 木围栏（加压处理松木，狗耳形栅栏板）
- 棕褐色乙烯基围栏
- 白色乙烯基围栏
- 5英尺铝制围栏
- 4英尺铝制围栏
输出格式
计算报价时，按以下格式呈现结果：
材料清单 - [项目名称/地址]
围栏类型：[类型]
总长度英尺数：[X]
大门配置：[X扇单扇，X扇双扇]
立柱
- - 4x4中间/角/端柱：[数量]
- 6x6大门立柱：[数量]
横梁
- - 2x4x8（围栏段）：[数量]
- 2x4x8（大门框架）：[数量]
- 2x4x8总数：[数量]
栅栏板（仅木围栏）
混凝土
- - 80磅袋装：[数量]
- 托盘（每托盘42袋）：[数量]
大门五金件
- - 门闩：[数量]
- 把手：[数量]
- 合页：[数量]
- 插销：[数量]
重要说明
- - 栅栏板和立柱数量始终向上取整。材料短缺意味着需要返工。
- 如果Reese提供粗略草图或描述转角/大门位置，请在计算前确认布局。
- 对于乙烯基和铝制围栏，立柱间距和段宽可能与木围栏不同。请向Reese确认规格是否与8英尺中心间距标准不同。
- 本技能不估算人工成本。人工费用单独定价。
